Small Precision Screwdriver Set for Electronics,22 in 1 Mini Screwdriver Set with 22 S2 Magnetic Screw Driver Bits and Extendable Handle,Repair Kit for Eyeglass Computer Laptop Watch Jewelers

I bought this after having already purchased both variations of the smaller screwdriver sets which means this purchase was far more a want than a need. Nanch's screwdriver sets are top notch & hands down my favorites out of all the many others I've laid hands on.

I've been using these screwdrivers since 2017 when I started working in research and development at a major aerospace company- they kept these in their lab.. I absolutely freaking love them! The screwdriver shaft extends, and there's a rotateable knob at the end of the handle for easy turning. I keep a set at home, one at work, and one at my parents' house. I often throw it in a travel kit when I go to airsoft events, just in case.. It's saved more than a few weekends!

I’ve had this screwdriver set for nearly two years now. I thought I had written a review already but better late than never considering the abuse this tool has sustained.First off, the case is adequately made but was obviously well-planned. Each bit is held firmly in place and the driver portion is easily accessible.Secondly, the driver has a “balance” about it. The endcap rotates smoothly which ensures contact with fasteners you’re removing/installing. The nibbling provides plenty of grip even when applying lots of torque. Today, after almost two years, I realized that the shaft is extendable. This is a feature I wish I had known about and probably overlooked when making my purchase.Overall, this set is a very good value. It is well organized which makes it obvious when a bit is left out. I’ve attached some photos in hopes it helps you make a decision.

Thus screwdriver set is very durable, organized, and functional for a wide veriety of projects. I needed a narrow shift for a specific use and these worked perfectly. The mahnet is strong enough to hold screws without being so strong that it gets in your way. Great price for what you're getting.

I loved this set so much I bought a second. Tragically they're using a different alloy in the handle compared to older units.Immediately I picked up the handle and knew it wasnt the same. I could tell it weighed less in the hand.To confirm this, I measured each handle on a gram scale. In the photos the old set is on the left, new on is on right.

I bouth my firs set in 2016 stel work well, this one I bougth for my friend. Highly recomended.

This is a great set to have. It's the perfect combination of function over form and quality. Everything there serves a purpose and there's no unnecessary embellishments. Even so, they managed to make it look nice.. sexy even (Yeah I went there). One of the things that surprised me the most was the thought and care in the container itself. It's seamlessly smooth to select the appropriate bit, barely lifting up to release it from it's deceptively strong clasp. If you're using several bits in quick succession, you can leave them slightly raised up once removed from its clasp so it's easy to remember which ones you were using and change them out that much faster. The 'heel' if you will of the driver pivots laterally (spins) which allows you to keep your palm against it and not have to re-grip it entirely. There's a small piece of rubber along the shaft to aid in grip along with a fishnet cut-out of the shaft closer to the tip, again for grip. There's a fairly strong magnet to keep your bit in place. If you need an extra few inches, there's a little sliding cone you push up, pull your extension out, and it locks firmly in its extended position. It won't lock unless it's fully extended or retracted, so no in-between settings, but that's perfectly fine by me. The bits themselves I've been quite rough with frankly and they've taken the beating like a champ. The only bits I've noticed slight wear on so far is the smallest of the Phillips and flathead, however this I'm sure is entirely my fault as I've been using them to pry panels open shortly after removing the screws. It's a bad habit I need to stop before I damage the bits beyond hope. After you've finished your project or what-have-you, simply push in any raised bits that had been selected, close it up and be on your merry. Again I'll point out the container, flipping the top so it sits underneath was a clever space-saving idea which comes in handy for people like me with cluttered desks and shelves and lateral area is precious.. Can't afford to have half the case just being pointlessly obstructive. I understand I've been long-winded, my points wander around and I'm terrible with run-on ideas (or sentences), but this is hands-down one of my best purchases ever from Amazon.And just because I think no review is valid unless it points out some kind of flaw or defect, the only two bad things I can say about the product is this: the sliding coupling to extend or retract the bit is a bit sharp on the edge, just a little pain, a slight nuisance, but it's a subtle aggrevation I bear silently because it's a small price to pay for this precision tool made by Hephastus himself. And when the top is flipped under, the catch or clasp for the container just sits there useless, and God forbid if your workstation gets bumped or something and the container falls, the chances of damage to the clasp and hinges is much higher than if the clasp held the container in the open position.And one last thing this is a bit of constructive criticism I feel would be an easy and very cost-efficient way to improve the quality of future products. If, on the interior of the lid there was a thin strip of rubber or something similar so when you open the container and implement the new dual-use clasp to secure the container, there would then be some grip facing down on your work surface to keep it stable, if it needed to rest on slight angles or keep it from vibrating away.

Needed a new set of small screw driver set for my small projects. Very sturdy!